متالیزه کردن سطح پلی پروپیلن با استفاده از روش پاشش سرد و بررسی چسبندگی بین لایهی و خواص بدست آمده
عنوان اصلي به زبان ديگر
Metallization of polypropylene surface by cold spraying method and examination of interlayer adhesion and obtained properties
نام نخستين پديدآور
/داود کوشش وطن
وضعیت نشر و پخش و غیره
نام ناشر، پخش کننده و غيره
: مهندسی مکانیک
تاریخ نشرو بخش و غیره
، ۱۳۹۹
نام توليد کننده
، راشدی
مشخصات ظاهری
نام خاص و کميت اثر
۸۹ص
یادداشتهای مربوط به نشر، بخش و غیره
متن يادداشت
چاپی - الکترونیکی
یادداشتهای مربوط به پایان نامه ها
جزئيات پايان نامه و نوع درجه آن
کارشناسی ارشد
نظم درجات
ساخت و تولید
زمان اعطا مدرک
۱۳۹۹/۰۶/۲۶
کسي که مدرک را اعطا کرده
تبریز
یادداشتهای مربوط به خلاصه یا چکیده
متن يادداشت
متالیزه کردن سطوح پلیمری و ایجاد پوششصهای فلزی بر روی پلیمرصها با هدف ایجاد خواص جدید بر روی سطح پلیمر انجام میصشود .پاشش سرد یکی از بهترین روشصها برای ایجاد پوشش ضخیم فلزی بر روی پلیمرصها است که از دسته پاشش حرارتی محسوب میصگردد .در این روش عموما ذرات بین ۵ الی ۵۰ میکرومتر با سرعت ۳۰۰ الی ۱۲۰۰ متر بر ثانیه و بهصصورت جامد به سطح بستر برخورد کرده و اتصال بین ذرات و سطح بستر صورت میصگیرد .چسبندگی در این فرآیند از طریق تغییر شکل پلاستیک و ایجاد نیروصهای چسبندگی که ناشی از تماس بدون واسطه سطح بستر و ذرات است صورت میصگیرد .بدین ترتیب یک پوششص فلزی در سطوح پلیمری ایجاد میشود .در ایران تحقیقی مبنی بر متالیزه کردن سطح پلیمرصها با فرآیند پاشش سرد صورت نگرفته است .همچنین در سطح جهانی پژوهشصهای محدودی در زمینه پاشش سرد فشار بالا بر روی پلیمرصها انجام شده است .در این پایاننامه، یک دستگاه پاشش سرد با قابلیت کار در فشارهای بالا و پایین طراحی و ساخته شد .در مرحله بعد پوششصهای اولیه برای به دست آوردن پارامترصهای ورودی مناسب جهت ایجاد پوششصهای اصلی روی سطح پلی-پروپیلن ایجاد شد .پارامترصهای ورودی به دست آمده عبارتند از :فشارکاری ۱۵ بار، دمایصکاری ۱۸۰ درجه سانتی-گراد، فاصله نازل ۳ میلیصمتر، نرخ تغذیه ۲۵ گرم بر دقیقه و نرخ پیشروی ۱۱۲ میلیصمتر بر دقیقه .همچنین پوششصهای تولید شده شامل پوشش مس دو پاسه، پوشش روی دو پاسه، پوشش کامپوزیتی دو لایه مس و روی و پوشش دو لایه کامپوزیتی۴۰ zn) + (۶۰ Cuمیصباشد .برای بررسی پوششصها از نظر ساختار و کیفیت چسبندگی از تصاویر میکرسکوپ الکترونی، تصاویر آنالیز میدانی، خروجیEDAX ، و تست چسبندگیCut - Xاستفاده شد و تست آنتی باکتریال نیز به عمل آمد .نتایج به دست آمده نشان داد، ذرات مس و روی به میزان بالایی در سطح بستر پلیصپروپیلن نفوذ کرده و موجب تغیر شکل پلاستیک شدید شده است .تغییر شکل پلاستیک صورت گرفته همراه با حبس ذرات در بستر موجب ایجاد اتصال مناسب گردیده است .همچنین تغییر شکل پلاستیک شدید در اتصال بین دو ذره نیز مشاهده شد که باعث ایجاد اتصال موفق بین دانهصای شده است .با توجه به نمودارصهایEDAX ، به جهت شکست اکسید-های سطحی ذرات در اثر برخورد شدید با سطح بستر میزان اکسیداسیون پوششصهای حاصل نسبت به پودر مصرف شده کاهش چشمگیری داشته است .براساس تستCut - Xچسبندگی سطوح تولیدی بسیار بالا است .نتایج حاصل از تست آنتیصباکتریال دیسک دیفیوژن نشان داد که پوششصهای مس و روی خالص خواص آنتیصباکتریال بالایی ندارند .ولی دو نوع پوشش کامپوزیتی دو لایه مس و روی و پوشش کامپوزیتی مخلوط۴۰ zn) + (۶۰ Cuبه جهت ایجاد شرایط همصافزایی، خواص آنتیصباکتریال مطلوبی دارند
متن يادداشت
C operating temperature, 3 mm nozzle distance, 25 g / min feed rate and 112 mm/min advance rate. Also produced coatings include two-pass copper coating, two-pass zinc coating, two-layer copper and zinc composite coating and two-layer composite coating (60 Cu + 40 zn). Electron microscope images, field analysis images, EDAX output, and X Cut adhesion test were used to evaluate the coatings in terms of structure and adhesion quality, and antibacterial testing was performed. The results showed that copper and zinc particles penetrated to a high extent on the surface of polypropylene substrate and caused severe plastic deformation. The deformation of the plastic along with the trapping of particles in the bed has caused a proper connection. Severe plastic deformation was also observed at the junction between the two particles, resulting in a successful connection between the grains. According to EDAX diagrams, due to the breakdown of surface oxides of particles because of severe impact with the substrate surface, the oxidation rate of the resulting coatings compared to the powder used has decreased significantly. According to the X Cut test, the adhesion of production surfaces is very high. The results of antibacterial disk diffusion test showed that pure copper and zinc coatings do not have high antibacterial properties. However, two types of two-layer composite coatings, copper and zinc, and mixed composite coatings (60 Cu + 40 Zn) have desirable antibacterial properties in order to make synergistic conditions ░ Metallization of polymer surfaces and creation of metal coatings on polymers is done with the aim of creating new properties on the polymer surface. Cold spraying is one of the best methods to makeake a thick metal coating on polymers, which is considered as thermal spraying. In this method, particles between 5 to 50 micrometers with a speed of 300 to 1200 meters per second and solidly hit the bed surface and the connection between the particles and the bed surface is done. Adhesion in this process takes place through the deformation of the plastic and the creation of adhesion forces that result from the direct contact of the substrate surface and the particles, thus creating a metal coating on the polymer surfaces. In Iran, no research has been done on metallization of polymer surfaces by cold spraying process. There is also limited worldwide research on high pressure cold spraying on polymers .In this dissertation, a cold sprayer with the potential of operating at high and low pressures was designed and built. In the next step, initial coatings were produced to obtain the appropriate input parameters to make the main coatings on the polypropylene surface. The input parameters obtained are: 15 bar working pressure, 180
عنوان اصلی به زبان دیگر
عنوان اصلي به زبان ديگر
Metallization of polypropylene surface by cold spraying method and examination of interlayer adhesion and obtained properties
نام شخص به منزله سر شناسه - (مسئولیت معنوی درجه اول )