بررسی تأثير عمليات حرارتی كوئنچ- بخش بندي (Q-P) بر رفتار سايشي يك فولاد استحكام بالاي حاوي ميكروآلياژTi
نام نخستين پديدآور
سمیه امامعلی پور
وضعیت نشر و پخش و غیره
نام ناشر، پخش کننده و غيره
مهندسي مکانیک
تاریخ نشرو بخش و غیره
۱۴۰۱
مشخصات ظاهری
نام خاص و کميت اثر
۸۴ص.
مواد همراه اثر
سی دی
یادداشتهای مربوط به پایان نامه ها
جزئيات پايان نامه و نوع درجه آن
کارشناسی ارشد
نظم درجات
مواد شناسایی و انتخاب مواد مهندسی
زمان اعطا مدرک
۱۴۰۱/۰۶/۱۶
یادداشتهای مربوط به خلاصه یا چکیده
متن يادداشت
امروزه تحقیقات زیادی در راستای بهبود و توسعه فولادهای با خواص مکانیکی بالا در حال انجام است. عملیات حرارتی کوئنچ-بخشبندی (Q-P)، بعنوان نسل سوم از فولادهای پیشرفته با استحکام بالا (AHSS)، گسترش یافته¬اند که به دلیل دارا بودن مجموعه ای مناسب از استحکام و شکل پذیری بالا می¬توان آن¬ها را در ساخت انواع قطعات صنعتی و حتی بعنوان ورق مورد استفاده قرار داد. سایش مواد، یک فرایند تخریب سطح در اثر مالش جامدات است که منتج به کاهش اندازه قطعات در جهت عمود بر سطح مالشی می¬شود. میزان سایش در لغزش دو قطعه، بستگی به خواص قطعات، جنس مواد، رفتار سطوح مالشی و کیفیت سطوح و همچنین به شرایط حرکتی آنها مانند بار اعمالی، دما، نوع روانکار و ... دارد. با توجه به ویژگی سطوح برخورد، تمایز بین سایش خشک، سایش با روانکاری مرزی و سایش با مواد ساینده به وجود می آید. بسته به تغییر شکل لایه های سطحی، سایش هنگام برخورد الاستیکی، سایش هنگام برخورد پلاستیکی و سایش هنگام برش میکروسکوپی، از هم متمایز می¬گردند. در این پژوهش فولادی با ترکیب شیمیایی ~ 0.2 wt%C~ 2 wt%Mn~ 1.5 wt% Si~ 0.08 wt% Ti Fe مورد مطالعه قرار خواهد گرفت. برای تسهیل آلیاژسازی و به حداقل رساندن درصد تلفات و کسب یک ساختار همگن، تمامی عناصر آلیاژی اضافه شده به فولاد بصورت فروآلیاژ به مذاب اضافه خواهند شد. آلیاژ مزبور در یک کوره ذوب القایی تحت خلاء (VIM) با دمای بارریزی 1650 ℃-1600 ذوب و به صورت شمش تولید خواهد شد. عملیات همگن سازی در دمای1200℃ به مدت 3 ساعت تحت اتمسفر آرگون انجام و شمش مزبور در کوره سرد خواهد شد. نمونه های مورد استفاده در تست سایش و بررسی ریزساختار، توسط یک دستگاه برش با سیم (وایرکات) از شمش مربوطه برش داده شده و سپس تحت عملیات سنگ زنی و سنباده زنی بعدی قرار خواهند گرفت. عملیات حرارتی Q-P بر روی نمونه های آماده شده در دماهای 20 Ms± ، 40 Ms± ، 60 Ms± و محدوده ی زمانی 100-1000 ثانیه انجام و نمونه های عملیات حرارتی شده از نظر ریزساختاری توسط میکروسکوپ نوری و میکروسکوپ الکترونی روبشی (SEM) مطالعه خواهند شد. آنالیز فازی نمونه ها با استفاده از پراش اشعه X (XRD) و خواص مکانیکی آنها با استفاده از تست سایش به روش بلوک روی رینگ و سختی سنجی بررسی خواهند شد. هدف از پژوهش حاضر ایجاد رابطه ای بین عملیات حرارتیQ-P ، ریز ساختار و خواص مکانیکی و حصول شرایط بهینه برای کسب بالاترین مقاومت سایشی در فولاد مورد مطالعه است .
متن يادداشت
Nowadays, a lot of research is being done in order to improve and develop steels with high mechanical properties. Quench-partition heat treatment (Q-P), as the third generation of advanced high-strength steels (AHSS), have been developed, which can be used in the manufacture of various industrial parts and It was even used as a sheet. Wear of materials is a surface destruction process due to the rubbing of solids, which results in the reduction of the size of the parts in the direction perpendicular to the rubbing surface. The amount of wear in the sliding of two parts depends on the properties of the parts, the material, the behavior of the rubbing surfaces and the quality of the surfaces, as well as their movement conditions such as applied load, temperature, type of lubricant, etc. According to the characteristics of the contact surfaces, a distinction is made between dry wear, wear with boundary lubrication and wear with abrasive materials. Depending on the deformation of the surface layers, wear during elastic contact, wear during plastic contact and wear during microscopic cutting are distinguished from each other. In this research, steel with the chemical composition of Fe~ 0.2 wt% C~ 2wt% Mn~ 1.5wt% Si~ 0.08wt% Ti will be studied. To facilitate alloying and to minimize the percentage of losses and obtain a homogeneous structure, all the alloying elements added to the steel will be added to the melt as ferroalloys. Said alloy will be melted in a vacuum induction melting furnace (VIM) with a discharge temperature of 1600-1650°C and produced as ingots. The homogenization operation will be done at 1200°C for 3 hours under argon atmosphere and the said ingot will be cooled in the furnace. The samples used in the wear test and microstructure investigation will be cut from the relevant ingot by a wire cutting machine and then subjected to subsequent grinding and sanding operations. Q-P heat treatment was performed on the prepared samples at temperatures of Ms±20, Ms±40, Ms±60 and a time range of 100-1000 seconds, and the microstructure of the heat-treated samples was analyzed by optical microscope and scanning electron microscope (SEM). will be studied. The phase analysis of the samples will be done using X-ray diffraction (XRD) and their mechanical properties will be checked using the block-on-ring wear test and hardness measurement. The aim of the current research is to establish a relationship between Q-P heat treatment, microstructure and mechanical properties and to achieve optimal conditions to obtain the highest wear resistance in the studied steel
عنوانهای گونه گون دیگر
عنوان گونه گون
The effect of quenching - partitioning (Q-P) heat treatment on the wear behavior of a high strength steel containing Ti microalloy
نام شخص به منزله سر شناسه - (مسئولیت معنوی درجه اول )