بررسی تاثیر عملیات حرارتی سرمایش سریع و بخش بندی بر رفتار مکانیکی و ریزساختار فولاد DIN ۱.۶۵۸۲
عنوان اصلي به زبان ديگر
Investigation of the effect of quenching and partitioning heat treatment on mechanical behavior and microstructure of steel DIN ۱.۶۵۸۲
نام نخستين پديدآور
/سعید آرامش
وضعیت نشر و پخش و غیره
نام ناشر، پخش کننده و غيره
: فنی مهندسی مکانیک
تاریخ نشرو بخش و غیره
، ۱۳۹۸
نام توليد کننده
، میرزائی
مشخصات ظاهری
نام خاص و کميت اثر
۶۲ص
یادداشتهای مربوط به نشر، بخش و غیره
متن يادداشت
چاپی - الکترونیکی
یادداشتهای مربوط به پایان نامه ها
جزئيات پايان نامه و نوع درجه آن
کارشناسی ارشد
نظم درجات
مهندسی مواد- شناسایی و انتخاب مواد مهندسی
زمان اعطا مدرک
۱۳۹۸/۰۴/۱۲
کسي که مدرک را اعطا کرده
تبریز
یادداشتهای مربوط به خلاصه یا چکیده
متن يادداشت
در این تحقیق تاثیر عملیات حرارتی سرمایش سریع و بخش بندی بر رفتار مکانیکی و ریزساختار فولاد DIN۱.۶۵۸۲ مورد بررسی قرار گرفته است .عملیات حرارتی سرمایش سریع و بخشصبندی بر اساس نفوذ کربن از مارتنزیت غنی از کربن به آستنیت جهت پایدار سازی آن در دمای محیط صورت می گیرد .براین اساس نمونه های آستنیته شده، در دمای ۲۳۰ و ۲۵۰ Cکوئنچ و به مدت سه ساعت در دمای ۳۵۰ Cبخش بندی شدند .همچنین به منظور مقایسه رفتار مکانیکی فولاد در عملیات کوئنچ و تمپر و آستمپرینگ با عملیات بخش بندی، نمونه ها به ترتیب در دمای ۸۰ و C۳۵۰کوئنچ شدند .نتایج نشان داد که با انجام عملیات بخشصبندی میزان چقرمگی شکست نسبت به عملیات سخت کاری و تمپر افزایش یافته و به مقدار ۲۴ ژول رسید .با افزایش دمای کوئنچ مقدار چقرمگی شکست به طور تدریجی افزایش یافت .همچنین مقدار استحکام با کاهش دمای کوئنچ افزایش یافت و به بیشترین استحکام مربوط به نمونه سختکاری و تمپر با ساختار غالبا مارتنزیتی تمپر شده به مقدار MPa۱۵۱۴ است .بهترین ترکیب استحکام و انعطافصپذیری مربوط به نمونه کوئنچ شده در دمای ۲۳۰ Cو بخش بندی شده در دمای C۳۵۰با ساختار مارتنزیت تمپر شده و بینیت است .نتایج XRD نشان داد درصد آستنیت باقیمانده در نمونه ها بسیار ناچیز بود و پیک های مربوط به آستنیت باقیمانده مشاهده نشد .نتایج SEM از سطح مقطع شکست نشان داد نوع شکست برای نمونه آستمپر شده از نوع نرم و برای نمونه بخش بندی شده ترکیبی از شکست نرم و ترد بود
متن يادداشت
In this study, the effect of quenching and partitioning heat treatment on mechanical behaviour and microstructure DIN1.6582 steel fragmentation has been investigated. qunching and partitioning heat treatment based on carbon penetration from carbon-rich martensite to austenite to stabilize it at ambient temperature. On this basis, the prepared samples, at 230 C and 250 C, they were quenched and partitioning at 350 C for three hours. In order to compare mechanical behavior of steel in quenching, tempering and aestempering operations with partitioning operations Samples were quenched at 80 and 350 C, respectively. The results showed that the fracture toughness rate increased to 24 Jules by performing partitioning operations in comparison with hardening and tempering operations as the temperature of the quench increases, the fracture toughness rate increases gradually. Also, the strength has increased with a decrease in the temperature of the quench so that the highest strength of the hardening and tempering sample is with a tempering martensitic structure of 1514 MPa. The best combination of strength and flexibility is associated with a quench sample at 230 C and partitioning into a temperature of 350 C with a tempered martensitic and bainite structure. XRD results showed that residual austenite percentage was very low in the samples, and no residual austenite peaks were observed. The SEM results from the fracture cross-section showed that the failure type for the austempered sample was of soft type and, for partitioning fraction sample was a combination of soft and crunchy fracture
عنوان اصلی به زبان دیگر
عنوان اصلي به زبان ديگر
Investigation of the effect of quenching and partitioning heat treatment on mechanical behavior and microstructure of steel DIN ۱.۶۵۸۲
نام شخص به منزله سر شناسه - (مسئولیت معنوی درجه اول )