بررسی و اعمال پوشش نانو ذرات TiO۲ آلاییده شده با آهن و سیلیکون بر روی زیر پایه بدنه لعاب خورده به روش اسپری
عنوان اصلي به زبان ديگر
Investigation and Application of Coating of TiO۲ Nanoparticles Affected by Iron and Silicon on the Substrate of the Foamed Foam by Spray Metho
نام نخستين پديدآور
/اکبر عابدینی
وضعیت نشر و پخش و غیره
نام ناشر، پخش کننده و غيره
: فنی مهندسی مکانیک
تاریخ نشرو بخش و غیره
، ۱۳۹۷
نام توليد کننده
، افشاری
مشخصات ظاهری
نام خاص و کميت اثر
۹۶ص
یادداشتهای مربوط به نشر، بخش و غیره
متن يادداشت
چاپی - الکترونیکی
یادداشتهای مربوط به پایان نامه ها
جزئيات پايان نامه و نوع درجه آن
کارشناسی ارشد
نظم درجات
مهندسی مواد- متالوژی
زمان اعطا مدرک
۱۳۹۷/۰۶/۲۰
کسي که مدرک را اعطا کرده
تبریز
یادداشتهای مربوط به خلاصه یا چکیده
متن يادداشت
نانوذرات فوتوکاتالیست دی اکسید تیتانیم به دلیل دارا بودن انرژی باند ممنوعه برابر ۲/۳ الکترون ولت قادر به جذب طول موجهای فرابنفش نزدیک می باشند .بنابراین کل انرژی خورشیدی قابل جذب توسط این ذرات بین ۳ تا ۴ درصد خواهد بود و به همین دلیل کارایی نانوذرات ۲TiO در حضور نور مرئی پایین می باشد .برای بهبود خواص فوتوکاتالیستی این نانوذرات در حضور نور مرئی از آلاینده های مختلف استفاده می شود .در فرآیند فوتوکاتالیستی، هر چه ذرات ۲TiO کوچکتر باشد، ضریب عملکرد افزایش می یابد .در این پژوهش سعی بر این است که با بکارگیری عناصر آهن و سیلیکون به عنوان آلاینده ضمن تشکیل یک پوشش خودتمیزشونده ۲TiO ، توانایی فعال سازی سطح در محدوده نور مرئی ایجاد شود .هدف از پوشش دهی، افزایش فعالیت فتوکاتالیستی و آب دوستی پوشش در محدوده خارج از اشعه UV و کاهش انرژی باند ممنوعه ی تیتانیا بوده پوشش دهی به روش سل ژل و با تکنیک اسپری بر سطح بدنه لعاب خورده انجام گرفت .و نتایج زیر حاصل شد .افزودن آلاینده Fe باعث کاهش اندازه بلورک ها از nm ۴۲ بهnm ۲۵ در حضور ۲۵/۲ درصد Fe می شود .نتایج آنالیز اشعه ایکس نمونه های آلاییده شده با درصدهای مختلف Si نشان می دهد که با افزایش درصد استفاده از Si میزان تبدیل فاز آناتاز به روتایل کاهش می یابد و در حضور ۲۵/۲ درصد Si مقدار فاز روتایل تقریبا به صفر می رسد .بررسی رفتار فوتوکاتالیستی نمونه ها در نور مرئی و فرابنفش در حضور همزمان آلاینده هایSi - Fe نشان داد که نمونه حاوی ۲۵/۲ درصد Fe و ۲۵/۲ درصد Si نسبت به نمونه های دیگر، نتایج بهتری داشت
متن يادداشت
Titanium dioxide photocatalytic nanoparticles can absorb the nearultraviolet wave lengths due to their band gap energy of 3.2 ev. Therefore, the total solar energy absorbed by these particles will be between 3 and 4 , which is why the performance of TiO2 nanoparticles is low in the presence of visible light. In order to improve the photocatalytic properties of these nanoparticles in the presence of visible light, various pollutants are used. In the photocatalytic process, the smaller the TiO2 particles, the coefficient of performance increases. In this research, it is tried to create the ability to activate surface in the visible light range by using iron and silicon as a pollutant while forming an self-healing coating TiO2 . The purpose of the coating was to increase the photocatalytic activity and hydrophilicity of the coating in the area outside of the UV rays and reduce the energy of the banned Titanium band, and the coating was performed by sol-gel method and spray technique on the surface of the enamelled body. The following results were obtained. The addition of Fe pollutants reduces the size of crystals from 42 nm to 25 nm in the presence of 2.25 Fe. X-ray analysis of samples contaminated with different percentages of Si shows that with an increase in the percentage of Si application, the conversion of anatase to rutile phase decreases, and in the presence of 2.25 Si, the amount of the rutile phase reaches zero. The photocatalytic behavior of samples in visible light and ultraviolet light in the presence of Fe-Si pollutants show that the samples containing Fe 2.25 Fe and 2.25 Si show better results than other samples
عنوان اصلی به زبان دیگر
عنوان اصلي به زبان ديگر
Investigation and Application of Coating of TiO۲ Nanoparticles Affected by Iron and Silicon on the Substrate of the Foamed Foam by Spray Metho
نام شخص به منزله سر شناسه - (مسئولیت معنوی درجه اول )