اندازه گیری دقیق تغییر شکل خاک ، اساس مدل سازی موفقیت آمیز در مسائل ژئوتکنیکی است و یکی از روشهایی که در چند سال اخیر و بدلیل مزایای بسیار، مورد توجه محققین قرار گرفته است استفاده از تصاویر دیجیتالی می باشد .این تکنیک بر اساس تقسیم بندی تصاویر گرفته شده از توده خاک تحت تغییر شکل به پچ های متعدد و اندازه گیری میزان جابجایی پچ ها مابین تصاویر متوالی با کمک پردازش تصویری استوار است .در این تحقیق با معرفی PIV بعنوان روشی مناسب در بررسی میدان تغییر شکل توده خاک ، به بررسی تراکم دینامیکی و عوامل مختلف تاثیر گذار بر آن با استفاده ازمدلسازی فیزیکی ماسه سست پرداخته می شود.جهت تخمین میزان بهسازی در اعماق مختلف از کرنشهای ایجاد شده درمدل استفاده می گردد .ضربات بوسیله وزنه های نیم استوانه ای فلزی بر سطح ماسه وارد گردیده و با ترکیبات مختلف وزنه ها ، اثر عواملی مانند وزن ، ارتفاع سقوط وسطح مقطع کوبه ، شدت انرژی کوبش و تعداد ضربات ، به منظور بهینه سازی عملیات کوبش مورد بررسی قرار گرفته و رابطه ای میان عوامل تاثیر گذار بر تراکم برقرار شده است. پس از هر ضربه قطر و عمق حفره ایجاد شده اندازه گیری شده است که می توان با برقراری رابطه ای میان عمق حفره از یک سو و پارامترهای تاثیر گذار در تراکم دینامیکی خاک از سویی دیگر ، معیاری برای سنجش و بازرسی تراکم دینامیکی یافت.
Accurate measurement of soil deformation is fundamental to the success of geotechnical modeling.One of the methods that have received a great attention in recent years because of numerous benefits , is the use of digital images.This technique is on the basis of division of taken images from soil mass under deformation in to several patches and measurement of displacements between frequent images with aide of image processing.In this research with introduction of PIV as an appropriate way in investigation of displacement fields of soil mass, has been focussed on the study of dynamic compaction and diverse influencity factors with the physical modeling of loose sand .To assess degree and depth of improvement , maximum volumetric strain that was generated in the soil mass , were used.Tamping executed by raising and dropping semi-cylindrical steel tampers on the surface of loose sand deposit and with repeating the process for different combinations of tampers the influence of some factors like weight,drop height ,area of tamper ,applied energy intensity and number of drops, in order to optimaize the compaction process, has been investigated.By using all resulted data was made some correlations between dynamic compaction parameters and influence depth, and print spacing. After each impact the depth and width of crater has been measured. With correlating crater depth and influential factors in dynamic compaction ,a criteria for assess and inspection of dyndmhc compaction is obtainable.